Juniper NetScreen Password

下記の資料から

NetScreen50が入荷してきましたので,初期化を致しました。

Googleで検索すると,詳細に記述されている記事を参考に工場出荷状態にしました。
その作業メモです。

まず,Ciscoコンソールケーブルを使い本体と接続。

Login:,Password:ともに本体のシリアル番号を入力。

初期化してもよいかという表示がされるので,Yを選択。

その後は,Login:,Password:ともnetscreen, netscreenでログイン可能。

後は,get system等のコマンドをたたき,内容を確認するだけです。

!!! Lost Password Reset !!! You have initiated a command to reset the device to
factory defaults, clearing all current configuration and settings. Would you lik
e to continue? y/[n] y

!! Reconfirm Lost Password Reset !! If you continue, the entire configuration of
the device will be erased. In addition, a permanent counter will be incremented
to signify that this device has been reset. This is your last chance to cancel
this command. If you proceed, the device will return to factory default configur
ation, which is: System IP: 192.168.1.1; username: netscreen, password: netscree
n. Would you like to continue? y/[n] y
In reset …

NetScreen NS-25/50 Boot Loader Version 3.0.0 (Checksum: D1C6421F)
Copyright (c) 1997-2003 NetScreen Technologies, Inc.

Total physical memory: 128MB
Test – Pass
Initialization – Done

Model Number: NS-50

Hit any key to run loader
Hit any key to run loader
Hit any key to run loader
Hit any key to run loader

Loading default system image from on-board flash disk…

Ignore image authentication!

Start loading…
…………………………………………
Done.

Juniper Networks, Inc
Copyright, 1997-2004

Version 5.0.0r8.0
Load Manufacture Information … init manufacture info Done
Load NVRAM Information … (5.0)Done
Install module init vectors
Verify ACL register default value (at hw reset) … Done
Verify ACL register read/write … Done
Verify ACL rule read/write … Done
Verify ACL rule search … Done
MD5(“a”) = 0cc175b9 c0f1b6a8 31c399e2 69772661
MD5(“abc”) = 90015098 3cd24fb0 d6963f7d 28e17f72
MD5(“message digest”) = f96b697d 7cb7938d 525a2f31 aaf161d0
Verify DES register read/write … Done
Install modules (00707000,00c5c8e0) … load dns table : dns table file do not e
xist.

Initializing DI 1.1.0-ns
*********************************************************
System time: 11 June 2010 09:39:39
If this is the initial device startup,
use the “set clock” command to set the system clock.
*********************************************************
system init done..
login: System change state to Active(1)

login:

ns50-> get system
Product Name: NS50
Serial Number: **********, Control Number: 00000000
Hardware Version: 4010(0)-(00), FPGA checksum: 00000000, VLAN1 IP (0.0.0.0)
Software Version: 5.0.0r8.0, Type: Firewall+VPN
Base Mac: 0010.db94.1f50
File Name: ns50ns25.5.0.0r8.0, Checksum: f5e8bcce

Date 06/11/2010 09:42:14, Daylight Saving Time enabled
The Network Time Protocol is Disabled
Up 0 hours 1 minutes 23 seconds Since 11 June 2010 09:40:51
Total Device Resets: 1, Last Device Reset at: 06/11/2010 08:39:11

System in NAT/route mode.

Use interface IP, Config Port: 80
User Name: netscreen

Interface ethernet1:
number 0, if_info 0, if_index 0, mode nat
link down, phy-link down
vsys Root, zone Trust, vr trust-vr
— more —
dhcp client disabled
PPPoE disabled
*ip 192.168.1.1/24 mac 0010.db94.1f50
*manage ip 192.168.1.1, mac 0010.db94.1f50
route-deny disable
Interface ethernet2:
number 5, if_info 2040, if_index 0, mode nat
link down, phy-link down
vsys Root, zone DMZ, vr trust-vr
dhcp client disabled
PPPoE disabled
*ip 0.0.0.0/0 mac 0010.db94.1f55
*manage ip 0.0.0.0, mac 0010.db94.1f55
Interface ethernet3:
number 6, if_info 2448, if_index 0, mode route
link down, phy-link down
vsys Root, zone Untrust, vr trust-vr
dhcp client disabled
PPPoE disabled
*ip 0.0.0.0/0 mac 0010.db94.1f56
*manage ip 0.0.0.0, mac 0010.db94.1f56
Interface ethernet4:
— more —
number 7, if_info 2856, if_index 0, mode nat
link down, phy-link down
vsys Root, zone HA, vr trust-vr
*ip 0.0.0.0/0 mac 0010.db94.1f57
ns50->